Wiko Harry 2
Wiko Harry 2 is a Wiko firmware file listed under Wiko, distributed as Wiko_Harry_2_MT6739_V01.16_011019_8.1.0.zip with a download size of 1 GB. It is built for the MediaTek MT6739 chipset and runs Android 8.1 (Oreo). It is flashed with SP Flash Tool. It was published on June 16, 2026. This page has been viewed 13 times. It is available to download free of charge. Before flashing, verify the file matches your exact device model and back up your data.
About Wiko Harry 2
Looking for the official stock firmware for your Wiko Harry 2? You're in the right place. Below is the original Wiko flash file you need to restore your device, whether you're fixing a software issue or starting fresh. Whether an update corrupted the system or a root attempt went wrong, the factory ROM puts the Wiko Harry 2 back to square one. File Name: Wiko_Harry_2_MT6739_V01.16_011019_8.1.0.zip File Size: 1 GB Before flashing, back up your data (the process wipes the device), charge above 50 percent, and install the correct USB drivers on your computer. After flashing, allow a few minutes for the first boot. From there the Wiko Harry 2 should run like a brand new unit.
File Details
| File name | Wiko Harry 2 |
|---|---|
| Package | Wiko_Harry_2_MT6739_V01.16_011019_8.1.0.zip |
| Brand / Platform | Wiko |
| Category | Wiko |
| Chipset | MediaTek MT6739 |
| Android version | Android 8.1 (Oreo) |
| Flash tool | SP Flash Tool |
| Package format | ZIP archive |
| File size | 1 GB |
| Date added | June 16, 2026 |
| Price | Free |
How to flash Wiko Harry 2 with SP Flash Tool
- Confirm Wiko Harry 2 matches your exact device model and that the phone uses the MT6739 chipset.
- Back up your personal data, as flashing firmware can erase the device. Charge the battery above 50%.
- Download the file (1 GB) using the button above and extract it on a Windows PC.
- Install the MediaTek VCOM / USB drivers, then open SP Flash Tool.
- In the tool, load the scatter file (MTxxxx_Android_scatter.txt) from the extracted folder.
- Start the flash, then power the phone off, then connect it (hold Volume Up or Down if it is not detected).
- Wait for the success message before disconnecting. Use "Download Only" — "Format All + Download" erases IMEI/NVRAM calibration.
Guides for this firmware
- MT6739 Firmware Guide: Flashing Tools and InstructionsThe MT6739 is a MediaTek chipset used in a wide variety of budget Android smartphones and tablets. To reflash or unbrick a device using this chipset, you will need the correct firmware for your…
- SP Flash Tool: Download Only vs Format All + DownloadSP Flash Tool is a utility used to flash firmware onto devices powered by MediaTek chipsets. When using this tool, you must choose between different download modes; "Download Only" is the recommended…
- Installing MediaTek VCOM Drivers for SP Flash ToolTo flash firmware on a MediaTek-based device, you must use the SP Flash Tool in conjunction with MediaTek VCOM USB drivers. These drivers allow your computer to communicate with the device's chipset…
Frequently asked questions
Is Wiko Harry 2 free to download?
Yes, Wiko Harry 2 can be downloaded free of charge from this page.
How large is the download?
The Wiko Harry 2 package is 1 GB.
Which tool do I need to flash Wiko Harry 2?
Wiko Harry 2 is MediaTek MT6739 firmware, so it is flashed with SP Flash Tool using the scatter file (MTxxxx_Android_scatter.txt).
What Android version is Wiko Harry 2?
This firmware is Android 8.1 (Oreo).
Which devices is this firmware for?
This file is intended for Wiko devices. Always confirm it matches your specific model before flashing.