Vertex Tab 4G 10-1
Vertex Tab 4G 10-1 is a Vertex firmware file listed under Vertex, distributed as Vertex_Tab_4G_10-1_MT6737M_R07_20180202.zip with a download size of 1 GB. It is built for the MediaTek MT6737M chipset, with a firmware build date of February 02, 2018. It is flashed with SP Flash Tool. It was published on June 16, 2026. This page has been viewed 32 times. It is available to download free of charge. Before flashing, verify the file matches your exact device model and back up your data.
About Vertex Tab 4G 10-1
Looking for the official stock firmware for your Vertex Tab 4G 10-1? You're in the right place. Below is the original Vertex flash file you need to restore your device, whether you're fixing a software issue or starting fresh. Whether an update corrupted the system or a root attempt went wrong, the factory ROM puts the Vertex Tab 4G 10-1 back to square one. File Name: Vertex_Tab_4G_10-1_MT6737M_R07_20180202.zip File Size: 1 GB Copy your data somewhere safe, top up the battery, grab a working USB cable, and confirm the proper drivers are set up before you start. After flashing, allow a few minutes for the first boot. From there the Vertex Tab 4G 10-1 should run like a brand new unit.
File Details
| File name | Vertex Tab 4G 10-1 |
|---|---|
| Package | Vertex_Tab_4G_10-1_MT6737M_R07_20180202.zip |
| Brand / Platform | Vertex |
| Category | Vertex |
| Chipset | MediaTek MT6737M |
| Build date | February 02, 2018 |
| Flash tool | SP Flash Tool |
| Package format | ZIP archive |
| File size | 1 GB |
| Date added | June 16, 2026 |
| Price | Free |
How to flash Vertex Tab 4G 10-1 with SP Flash Tool
- Confirm Vertex Tab 4G 10-1 matches your exact device model and that the phone uses the MT6737M chipset.
- Back up your personal data, as flashing firmware can erase the device. Charge the battery above 50%.
- Download the file (1 GB) using the button above and extract it on a Windows PC.
- Install the MediaTek VCOM / USB drivers, then open SP Flash Tool.
- In the tool, load the scatter file (MTxxxx_Android_scatter.txt) from the extracted folder.
- Start the flash, then power the phone off, then connect it (hold Volume Up or Down if it is not detected).
- Wait for the success message before disconnecting. Use "Download Only" — "Format All + Download" erases IMEI/NVRAM calibration.
Guides for this firmware
- MT6737M Firmware: Flashing Guide and Supported DevicesThe MT6737M is a MediaTek chipset used in a wide variety of budget Android smartphones and tablets. To reflash or unbrick a device using this chipset, you will need the correct firmware for your…
- SP Flash Tool: Download Only vs Format All + DownloadSP Flash Tool is a utility used to flash firmware onto devices powered by MediaTek chipsets. When using this tool, you must choose between different download modes; "Download Only" is the recommended…
- Installing MediaTek VCOM Drivers for SP Flash ToolTo flash firmware on a MediaTek-based device, you must use the SP Flash Tool in conjunction with MediaTek VCOM USB drivers. These drivers allow your computer to communicate with the device's chipset…
Frequently asked questions
Is Vertex Tab 4G 10-1 free to download?
Yes, Vertex Tab 4G 10-1 can be downloaded free of charge from this page.
How large is the download?
The Vertex Tab 4G 10-1 package is 1 GB.
Which tool do I need to flash Vertex Tab 4G 10-1?
Vertex Tab 4G 10-1 is MediaTek MT6737M firmware, so it is flashed with SP Flash Tool using the scatter file (MTxxxx_Android_scatter.txt).
Which devices is this firmware for?
This file is intended for Vertex devices. Always confirm it matches your specific model before flashing.