Lava

Lava Benco Y30 AF9030

Lava_Benco_Y30_AF9030_S134_INT_21E28_193833_SPD.zip.zip.zip
June 16, 2026 Lava 936 MB Lava

Lava Benco Y30 AF9030 is a Lava firmware file listed under Lava, distributed as Lava_Benco_Y30_AF9030_S134_INT_21E28_193833_SPD.zip.zip.zip with a download size of 936 MB. It is built for Unisoc (Spreadtrum)-based devices. It is flashed with SPD ResearchDownload (or UpgradeDownload). It was published on June 16, 2026. This page has been viewed 6 times. It is available to download free of charge. Before flashing, verify the file matches your exact device model and back up your data.

File Size
936 MB
Download Free

About Lava Benco Y30 AF9030

If your Lava Benco Y30 AF9030 has been giving you trouble, reinstalling the stock firmware is often the cleanest fix. Here you'll find the full Lava flash package along with the details to check before you begin. It can rescue a bricked handset, fix IMEI or baseband errors, and give the Lava Benco Y30 AF9030 a fresh start without the clutter that builds up over time. File Name: Lava_Benco_Y30_AF9030_S134_INT_21E28_193833_SPD.zip.zip.zip File Size: 936 MB Copy your data somewhere safe, top up the battery, grab a working USB cable, and confirm the proper drivers are set up before you start. After flashing, allow a few minutes for the first boot. From there the Lava Benco Y30 AF9030 should run like a brand new unit.

File Details

File nameLava Benco Y30 AF9030
PackageLava_Benco_Y30_AF9030_S134_INT_21E28_193833_SPD.zip.zip.zip
Brand / PlatformLava
CategoryLava
PlatformUnisoc (Spreadtrum)
Flash toolSPD ResearchDownload (or UpgradeDownload)
Package formatZIP archive
File size936 MB
Date addedJune 16, 2026
PriceFree

How to flash Lava Benco Y30 AF9030 with SPD ResearchDownload

  1. Confirm Lava Benco Y30 AF9030 matches your exact device model and that it is intended for Lava hardware.
  2. Back up your personal data, as flashing firmware can erase the device. Charge the battery above 50%.
  3. Download the file (936 MB) using the button above and extract it on a Windows PC.
  4. Install the SPD / Unisoc USB drivers, then open SPD ResearchDownload (or UpgradeDownload).
  5. In the tool, load the .pac firmware file from the extracted folder.
  6. Start the flash, then press Start in the tool, then connect the powered-off phone while holding Volume Down (boot key).
  7. Wait for the success message before disconnecting. Leave "Erase NV" unticked unless you intend to wipe IMEI and calibration data.

Frequently asked questions

Is Lava Benco Y30 AF9030 free to download?

Yes, Lava Benco Y30 AF9030 can be downloaded free of charge from this page.

How large is the download?

The Lava Benco Y30 AF9030 package is 936 MB.

Which tool do I need to flash Lava Benco Y30 AF9030?

Lava Benco Y30 AF9030 is Unisoc (Spreadtrum) firmware, so it is flashed with SPD ResearchDownload (or UpgradeDownload) using the .pac firmware file.

Which devices is this firmware for?

This file is intended for Lava devices. Always confirm it matches your specific model before flashing.

More Lava files

Back to Lava