Intex Aqua Classic
Intex Aqua Classic is a Intex firmware file listed under Intex, distributed as Intex_Aqua_Classic_V03_Indian_SER_20160530_SPD.zip with a download size of 788 MB. It is built for Unisoc (Spreadtrum)-based devices, with a firmware build date of May 30, 2016. It is flashed with SPD ResearchDownload (or UpgradeDownload). It was published on June 16, 2026. This page has been viewed 10 times. It is available to download free of charge. Before flashing, verify the file matches your exact device model and back up your data.
About Intex Aqua Classic
Looking for the official stock firmware for your Intex Aqua Classic? You're in the right place. Below is the original Intex flash file you need to restore your device, whether you're fixing a software issue or starting fresh. Whether an update corrupted the system or a root attempt went wrong, the factory ROM puts the Intex Aqua Classic back to square one. File Name: Intex_Aqua_Classic_V03_Indian_SER_20160530_SPD.zip File Size: 788 MB Back up your files, charge the Intex Aqua Classic past 50 percent, install the matching drivers, and only then begin. After flashing, allow a few minutes for the first boot. From there the Intex Aqua Classic should run like a brand new unit.
File Details
| File name | Intex Aqua Classic |
|---|---|
| Package | Intex_Aqua_Classic_V03_Indian_SER_20160530_SPD.zip |
| Brand / Platform | Intex |
| Category | Intex |
| Platform | Unisoc (Spreadtrum) |
| Build date | May 30, 2016 |
| Flash tool | SPD ResearchDownload (or UpgradeDownload) |
| Package format | ZIP archive |
| File size | 788 MB |
| Date added | June 16, 2026 |
| Price | Free |
How to flash Intex Aqua Classic with SPD ResearchDownload
- Confirm Intex Aqua Classic matches your exact device model and that it is intended for Intex hardware.
- Back up your personal data, as flashing firmware can erase the device. Charge the battery above 50%.
- Download the file (788 MB) using the button above and extract it on a Windows PC.
- Install the SPD / Unisoc USB drivers, then open SPD ResearchDownload (or UpgradeDownload).
- In the tool, load the .pac firmware file from the extracted folder.
- Start the flash, then press Start in the tool, then connect the powered-off phone while holding Volume Down (boot key).
- Wait for the success message before disconnecting. Leave "Erase NV" unticked unless you intend to wipe IMEI and calibration data.
Guides for this firmware
- Intex Firmware Guide: Finding and Flashing Stock ROMsTo reflash or unbrick an Intex device, you must use a stock ROM that matches your specific model and the corresponding flashing tool for its chipset. Most Intex devices utilize either MediaTek or…
- Connecting Unisoc Phones to SPD ResearchDownloadSPD ResearchDownload (also known as UpgradeDownload) is a specialized flashing tool used to install stock firmware on devices powered by Unisoc (Spreadtrum) chipsets. To connect a phone to this tool…
- Flashing .pac Files with SPD ResearchDownload GuideSPD ResearchDownload (also known as UpgradeDownload) is a specialized flashing tool used to install stock firmware on devices powered by Unisoc (Spreadtrum) chipsets. It is primarily used to unbrick…
Frequently asked questions
Is Intex Aqua Classic free to download?
Yes, Intex Aqua Classic can be downloaded free of charge from this page.
How large is the download?
The Intex Aqua Classic package is 788 MB.
Which tool do I need to flash Intex Aqua Classic?
Intex Aqua Classic is Unisoc (Spreadtrum) firmware, so it is flashed with SPD ResearchDownload (or UpgradeDownload) using the .pac firmware file.
Which devices is this firmware for?
This file is intended for Intex devices. Always confirm it matches your specific model before flashing.