Itel Prime Tab 1 W7002P
Itel Prime Tab 1 W7002P is a Itel firmware file listed under Itel, distributed as Itel_Prime_Tab_1_W7002P_V010_210521_10_SPD.zip with a download size of 1.22 GB. It is built for Unisoc (Spreadtrum)-based devices. It is flashed with SPD ResearchDownload (or UpgradeDownload). It was published on June 16, 2026. This page has been viewed 14 times. It is available to download free of charge. Before flashing, verify the file matches your exact device model and back up your data.
About Itel Prime Tab 1 W7002P
If your Itel Prime Tab 1 W7002P has been giving you trouble, reinstalling the stock firmware is often the cleanest fix. Here you'll find the full Itel flash package along with the details to check before you begin. It can rescue a bricked handset, fix IMEI or baseband errors, and give the Itel Prime Tab 1 W7002P a fresh start without the clutter that builds up over time. File Name: Itel_Prime_Tab_1_W7002P_V010_210521_10_SPD.zip File Size: 1.22 GB Back up everything important first, keep the battery above the halfway mark, use a cable you trust, and make sure the right drivers are installed. After flashing, allow a few minutes for the first boot. From there the Itel Prime Tab 1 W7002P should run like a brand new unit.
File Details
| File name | Itel Prime Tab 1 W7002P |
|---|---|
| Package | Itel_Prime_Tab_1_W7002P_V010_210521_10_SPD.zip |
| Brand / Platform | Itel |
| Category | Itel |
| Platform | Unisoc (Spreadtrum) |
| Flash tool | SPD ResearchDownload (or UpgradeDownload) |
| Package format | ZIP archive |
| File size | 1.22 GB |
| Date added | June 16, 2026 |
| Price | Free |
How to flash Itel Prime Tab 1 W7002P with SPD ResearchDownload
- Confirm Itel Prime Tab 1 W7002P matches your exact device model and that it is intended for Itel hardware.
- Back up your personal data, as flashing firmware can erase the device. Charge the battery above 50%.
- Download the file (1.22 GB) using the button above and extract it on a Windows PC.
- Install the SPD / Unisoc USB drivers, then open SPD ResearchDownload (or UpgradeDownload).
- In the tool, load the .pac firmware file from the extracted folder.
- Start the flash, then press Start in the tool, then connect the powered-off phone while holding Volume Down (boot key).
- Wait for the success message before disconnecting. Leave "Erase NV" unticked unless you intend to wipe IMEI and calibration data.
Guides for this firmware
- Connecting Unisoc Phones to SPD ResearchDownloadSPD ResearchDownload (also known as UpgradeDownload) is a specialized flashing tool used to install stock firmware on devices powered by Unisoc (Spreadtrum) chipsets. To connect a phone to this tool…
- Flashing .pac Files with SPD ResearchDownload GuideSPD ResearchDownload (also known as UpgradeDownload) is a specialized flashing tool used to install stock firmware on devices powered by Unisoc (Spreadtrum) chipsets. It is primarily used to unbrick…
- How to Use SPD ResearchDownload: Firmware Flashing GuideSPD ResearchDownload (also known as UpgradeDownload) is a specialized flashing tool used to install stock firmware on devices powered by Unisoc (Spreadtrum) chipsets. It allows technicians and users…
Frequently asked questions
Is Itel Prime Tab 1 W7002P free to download?
Yes, Itel Prime Tab 1 W7002P can be downloaded free of charge from this page.
How large is the download?
The Itel Prime Tab 1 W7002P package is 1.22 GB.
Which tool do I need to flash Itel Prime Tab 1 W7002P?
Itel Prime Tab 1 W7002P is Unisoc (Spreadtrum) firmware, so it is flashed with SPD ResearchDownload (or UpgradeDownload) using the .pac firmware file.
Which devices is this firmware for?
This file is intended for Itel devices. Always confirm it matches your specific model before flashing.