Itel Vision 1 Pro
Itel Vision 1 Pro is a Itel firmware file listed under Itel, distributed as Itel_Vision_1_Pro_L6502_IN_V030_20201218_10_SPD.zip with a download size of 1.5 GB. It is built for Unisoc (Spreadtrum)-based devices, with a firmware build date of December 18, 2020. It is flashed with SPD ResearchDownload (or UpgradeDownload). It was published on June 16, 2026. This page has been viewed 14 times. It is available to download free of charge. Before flashing, verify the file matches your exact device model and back up your data.
About Itel Vision 1 Pro
The Itel Vision 1 Pro runs on Itel's factory software, and sometimes you need to reinstall it from scratch. This page provides the genuine stock ROM so you can return the device to its original state. It can rescue a bricked handset, fix IMEI or baseband errors, and give the Itel Vision 1 Pro a fresh start without the clutter that builds up over time. File Name: Itel_Vision_1_Pro_L6502_IN_V030_20201218_10_SPD.zip File Size: 1.5 GB Back up your files, charge the Itel Vision 1 Pro past 50 percent, install the matching drivers, and only then begin. After flashing, allow a few minutes for the first boot. From there the Itel Vision 1 Pro should run like a brand new unit.
File Details
| File name | Itel Vision 1 Pro |
|---|---|
| Package | Itel_Vision_1_Pro_L6502_IN_V030_20201218_10_SPD.zip |
| Brand / Platform | Itel |
| Category | Itel |
| Platform | Unisoc (Spreadtrum) |
| Build date | December 18, 2020 |
| Flash tool | SPD ResearchDownload (or UpgradeDownload) |
| Package format | ZIP archive |
| File size | 1.5 GB |
| Date added | June 16, 2026 |
| Price | Free |
How to flash Itel Vision 1 Pro with SPD ResearchDownload
- Confirm Itel Vision 1 Pro matches your exact device model and that it is intended for Itel hardware.
- Back up your personal data, as flashing firmware can erase the device. Charge the battery above 50%.
- Download the file (1.5 GB) using the button above and extract it on a Windows PC.
- Install the SPD / Unisoc USB drivers, then open SPD ResearchDownload (or UpgradeDownload).
- In the tool, load the .pac firmware file from the extracted folder.
- Start the flash, then press Start in the tool, then connect the powered-off phone while holding Volume Down (boot key).
- Wait for the success message before disconnecting. Leave "Erase NV" unticked unless you intend to wipe IMEI and calibration data.
Guides for this firmware
- Connecting Unisoc Phones to SPD ResearchDownloadSPD ResearchDownload (also known as UpgradeDownload) is a specialized flashing tool used to install stock firmware on devices powered by Unisoc (Spreadtrum) chipsets. To connect a phone to this tool…
- Flashing .pac Files with SPD ResearchDownload GuideSPD ResearchDownload (also known as UpgradeDownload) is a specialized flashing tool used to install stock firmware on devices powered by Unisoc (Spreadtrum) chipsets. It is primarily used to unbrick…
- How to Use SPD ResearchDownload: Firmware Flashing GuideSPD ResearchDownload (also known as UpgradeDownload) is a specialized flashing tool used to install stock firmware on devices powered by Unisoc (Spreadtrum) chipsets. It allows technicians and users…
Frequently asked questions
Is Itel Vision 1 Pro free to download?
Yes, Itel Vision 1 Pro can be downloaded free of charge from this page.
How large is the download?
The Itel Vision 1 Pro package is 1.5 GB.
Which tool do I need to flash Itel Vision 1 Pro?
Itel Vision 1 Pro is Unisoc (Spreadtrum) firmware, so it is flashed with SPD ResearchDownload (or UpgradeDownload) using the .pac firmware file.
Which devices is this firmware for?
This file is intended for Itel devices. Always confirm it matches your specific model before flashing.