Huawei

Huawei Y330-U01

Huawei_Y330-U01_MT6572_V100R001C00B121_Burma_21052014_4.2.zip
June 16, 2026 Huawei 661 MB Huawei

Huawei Y330-U01 is a Huawei firmware file listed under Huawei, distributed as Huawei_Y330-U01_MT6572_V100R001C00B121_Burma_21052014_4.2.zip with a download size of 661 MB. It is built for the MediaTek MT6572 chipset and runs Android 4.2 (Jelly Bean), with a firmware build date of May 21, 2014. It is flashed with SP Flash Tool. It was published on June 16, 2026. This page has been viewed 16 times. It is available to download free of charge. Before flashing, verify the file matches your exact device model and back up your data.

File Size
661 MB
Download Free

About Huawei Y330-U01

Looking for the official stock firmware for your Huawei Y330-U01? You're in the right place. Below is the original Huawei flash file you need to restore your device, whether you're fixing a software issue or starting fresh. Whether an update corrupted the system or a root attempt went wrong, the factory ROM puts the Huawei Y330-U01 back to square one. File Name: Huawei_Y330-U01_MT6572_V100R001C00B121_Burma_21052014_4.2.zip File Size: 661 MB Back up your files, charge the Huawei Y330-U01 past 50 percent, install the matching drivers, and only then begin. After flashing, allow a few minutes for the first boot. From there the Huawei Y330-U01 should run like a brand new unit.

File Details

File nameHuawei Y330-U01
PackageHuawei_Y330-U01_MT6572_V100R001C00B121_Burma_21052014_4.2.zip
Brand / PlatformHuawei
CategoryHuawei
ChipsetMediaTek MT6572
Android versionAndroid 4.2 (Jelly Bean)
Build dateMay 21, 2014
Flash toolSP Flash Tool
Package formatZIP archive
File size661 MB
Date addedJune 16, 2026
PriceFree

How to flash Huawei Y330-U01 with SP Flash Tool

  1. Confirm Huawei Y330-U01 matches your exact device model and that the phone uses the MT6572 chipset.
  2. Back up your personal data, as flashing firmware can erase the device. Charge the battery above 50%.
  3. Download the file (661 MB) using the button above and extract it on a Windows PC.
  4. Install the MediaTek VCOM / USB drivers, then open SP Flash Tool.
  5. In the tool, load the scatter file (MTxxxx_Android_scatter.txt) from the extracted folder.
  6. Start the flash, then power the phone off, then connect it (hold Volume Up or Down if it is not detected).
  7. Wait for the success message before disconnecting. Use "Download Only" — "Format All + Download" erases IMEI/NVRAM calibration.

Frequently asked questions

Is Huawei Y330-U01 free to download?

Yes, Huawei Y330-U01 can be downloaded free of charge from this page.

How large is the download?

The Huawei Y330-U01 package is 661 MB.

Which tool do I need to flash Huawei Y330-U01?

Huawei Y330-U01 is MediaTek MT6572 firmware, so it is flashed with SP Flash Tool using the scatter file (MTxxxx_Android_scatter.txt).

What Android version is Huawei Y330-U01?

This firmware is Android 4.2 (Jelly Bean), built on May 21, 2014.

Which devices is this firmware for?

This file is intended for Huawei devices. Always confirm it matches your specific model before flashing.

More Huawei files

Back to Huawei